MOUSE & MAZE
                             GUIDING ROUTE TOOL  
                          DESIGNED BY TIMOTHY WEN
                            10/2008 PD SOFTWARE



COMMAND :

              I
             J K     ADD ELEMENT OF WALL TO BUILD MAZE.  
              M 


              Y
             G H     DELETE ELEMENT OF WALL TO BUILD MAZE.
              B


             ^Y
           ^G  ^H    JUST MOVE CURSOR,NO ADDING OR DELETING ELEMENT OF WALL.
             ^B 



              R      BEGIN TO RUN THE MOUSE.

              Q      QUIT THE PROGRAM.

              S      SAVE MAZE PATTERN 
                    
                     (PRESS "+" AND <RETURN> KEYS TO CANCLE IT).
 
                     (24 LETTERS OF FILENAME IS LIMITED).

              L      LOAD MAZE PATTERN.

                     (PRESS "+" AND <RETURN> KEYS TO CANCLE IT).
                    
              C      CLEAR DESIGNING AREA.

              X      SHOW THE SAVED MAZE FILES.

              U      CLEAR GUIDING ROUTE.

             ^F      IF YOU CAN'T LOAD THE MAZE OF OLD VERSION,
                     TRY THIS FUNCTION.

                     (PRESS "+" AND <RETURN> KEYS TO CANCLE IT).       

              F      GUIDING ROUTE MODE.
        
                     (PRESS "+" KEY TO CANCLE IT). 

                     (1000 STEPS OF GUIDING ROUTE IS LIMITED). 

                     (PRESS D KEY TO RESET IT AGAIN).

                     (PRESS 
                            I - TO MOVE UP
                            J - TO MOVE LEFT
                            K - TO MOVE RIGHT
                            M - TO MOVE DOWN

                            Q - TO MOVE UPPER LEFT
                            W - TO MOVE UPPER RIGHT
                            A - TO MOVE DOWN LEFT
                            S - TO MOVE DOWN RIGHT )

              V      SHOW THE GUIDING ROUTE.

                     (IF MAZE CHANGED AND THE ELEMENTS OF WALL STAND ON
                      THE GUIDING ROUTE,YOU MUST TO RESET THE ROUTE AGAIN.)



             ^O      CHANGE ORIGINAL POSITION OF THE MOUSE.
                     
                     (USE ^Y,^G,^H,^B TO MOVE THE MOUSE,
                      AND PRESS ^O AGAIN TO SET IT UP.)
                   
                     (NOTICE : 1.ORIGINAL POSITION CAN'T BE THE SAME
                                 PLACE AS TARGET POSITION.
                               2.ORIGINAL POSITION CAN'T BE THE SAME
                                 PLACE AS THE ELEMENTS OF WALL.
                               3.YOU MUST RESET AGAIN IF THE ABOVE HAPPENED.)         
        
             ^T      CHANGE TARGET POSITION OF THE MOUSE.
                    
                     (USE ^Y,^G,^H,^B TO MOVE THE MOUSE,
                      AND PRESS ^T AGAIN TO SET IT UP.)

                     (NOTICE : 1.TARGET POSITION CAN'T BE THE SAME
                                 PLACE AS ORIGINAL POSITION.
                               2.TARGET POSITION CAN'T BE THE SAME
                                 PLACE AS THE ELEMENTS OF WALL.
                               3.YOU MUST RESET AGAIN IF THE ABOVE HAPPENED.)         
 
             ^R      RETURN TO COMMON MODE.
                     
                     (TARGETS ARE THE EDGES OF DESIGNING AREA.)  

             ^S      SAVE GUIDING ROUTE.

                     (PRESS "+" AND <RETURN> KEYS TO CANCLE IT).
 
                     (24 LETTERS OF FILENAME IS LIMITED).


             ^I      LOAD GUIDING ROUTE.  

                     (PRESS "+" AND <RETURN> KEYS TO CANCLE IT).
 
                     
                      
MEANING OF NUMBERS IN COMMAND AREA :

       DOLLAR :      NUMBER OF WALL-ELEMENTS.
         STEP :      TOTAL NUMBER OF STEPS THAT MOUSE RUNS.
       RESTEP :      NUMBER OF REPEAT STEPS THAT MOUSE RUNS.

          CUT :      NUMBER OF SHORTCUT-STEPS. 
         GUIDE:      NUMBER OF GUIDING ROUTE-STEPS.
     

* 80 column card in slot 3 is needed.
* Set AppleWin's custom speed to fastest limit is much better.  
  (function "optimize route" will take hours if you don't raise up the speed.) 

Have fun
Timohy

salewts@yahoo.com.tw